Best Miter Saws Under $200 (2026)

The WEN MM0713 is a compact sliding saw. A dual-rail slide system lets the head move back and forth on two rails, so it crosscuts boards up to 11.5 inches wide, and the system is designed to sit flush against a wall. The 9.5-amp motor drives a 7-1/4-inch, 40-tooth carbide blade, a fine blade that gives a smooth cut on trim and plywood.

It miters 45 degrees in either direction with nine stops and bevels 45 degrees to the left, which covers most trim work but not the right-hand bevel of a dual-bevel saw. Compared with the DEKOPRO 10-inch, the WEN has a smaller blade and a slide that extends crosscut width to 11.5 inches, while the 10-inch is fixed and limited to the board width it can chop.

Ownership details are encouraging: two table extensions, a clamp, a dust port, a dust bag, a carry handle and a two-year warranty are included. The onboard LED shows the cut line, though you should still align the blade to a pencil mark. Check the fence for square before the first cut, because budget saws can ship slightly out. Hold a combination square against the fence and the blade, tilted to 90 degrees, and adjust the fence screws until no light shows. A saw that cuts square on the first board will keep cutting square for years, and one that does not will waste every piece of trim you feed it.

The DEKOPRO is a 10-inch single-bevel compound saw with a 13-amp motor that spins to 5,000 RPM. A 40-tooth blade ships on it, along with a large table, a clamp and a transparent blade guard that gives a clear view of the cut line. At 20.5 pounds it is light enough to carry to a job.

Compared with the WEN, the DEKOPRO has a larger blade and more motor, and a 10-inch blade cuts deeper in thick stock, such as a 4x4 post in a single pass at a right angle. What it lacks is a slide, so crosscut width is limited to roughly the blade's chop capacity, which is narrower than the WEN's sliding reach in boards.

For ownership, check the fence for square, tighten the miter lock and replace the blade for finish work. The saw head locks down for compact storage, which suits a garage shelf. If you cut 2x4s and 4x4s and trim, it is the stronger tool. A 13-amp motor also has more reserve when a 40-tooth blade meets a knot or a wet board, so it bogs less than the 9.5-amp WEN at the same feed rate. Plan to add a stand or a pair of sawhorses with a long support board, because a short table lets long boards tip and ruin the cut.

The Yumark is a 10-inch miter saw with an all-copper motor rated at 6,000 RPM no load. It weighs about 20 pounds and folds for storage, and its maker lists a dual 45-degree adjustable table with a thickened stopper. A spiral exhaust design cools the motor, and a shock-absorbing handle is meant to reduce fatigue.

Its 6,000 RPM figure is higher than the DEKOPRO's 5,000 RPM, but the amp rating is not listed, so power cannot be compared. Speed without a rated motor is not a promise of cutting power. Next to the WEN, it has a bigger blade but no slide.

Treat it as a basic chop saw for 2x lumber, trim and plastics, and check the fence and bevel for square before use. Parts and service are thin, so the sensible approach is to keep the packaging for returns and use the saw lightly. A 6,000 RPM blade also throws chips and dust faster, so wear eye and hearing protection, and let the blade reach full speed before it touches the wood, since a blade that is still spinning up can grab and kick.

The Ryobi is a cordless 7-1/4-inch compound miter saw, sold as a bare tool. Battery and charger are sold separately, so the price only makes sense if you already own ONE+ batteries. Ryobi's ONE+ system is one of the most widely used battery platforms, so many homeowners already have packs.

A cordless miter saw is a convenience tool. It runs anywhere, with no cord to trip on, and suits trim jobs in rooms without a convenient outlet. It gives up sustained power to corded saws like the WEN at 9.5 amps and the DEKOPRO at 13 amps.

For ownership, use a fully charged 4Ah or larger pack for best runtime, replace the stock blade with a fine finish blade for trim, and check that the fence is square. If you do not own ONE+ batteries, add the cost of a battery and charger before you decide. A battery that is fresh off the charger makes a visible difference on a saw like this, because voltage sags when a blade meets a knot and a half-flat pack slows the blade enough to burn the cut. Allow the blade to stop completely before lifting the head, since a coasting blade on a cordless saw is easy to forget.