Amazon affiliate links - we earn a commission.Affiliate disclosure

Buying guide · 12 min read · Updated 2026-11-19

Best Paper Shredders for Staples and Paper Clips (2026)

Six shredders that accept staples and paper clips, compared on how they handle metal fasteners, cut size, run time and bin size so you can skip the pre-sorting.

James MillerBy James MillerLead Machine Editor6 machines comparedSpec-sheet verified
Best Paper Shredders for Staples and Paper Clips

At a glance

Our top picks

Side by side

Spec comparison

MachineCapacityCutFastenersBinRun time
Amazon Basics 15-Sheet Cross-Cut Shredder, 6 Gal, Staples OKBest OverallAmazon Basics 15-Sheet Cross-Cut Shredder, 6 Gal, Staples OK15 sheetsCross-cut, 5.1 x 25.4 mmStaples and small clips6 gal wastebasketn/a
Bonsaii 12-Sheet Micro-Cut Shredder with Clips, Staples, 5.5 GalBest Micro-Cut OptionBonsaii 12-Sheet Micro-Cut Shredder with Clips, Staples, 5.5 Gal12 sheetsMicro-cut, P-4Staples, paper clips, cards5.5 gal, about 350 sheets5 minutes
Bonsaii 9-Sheet Cross-Cut Shredder for Home, Staples and ClipsBest Value CompactBonsaii 9-Sheet Cross-Cut Shredder for Home, Staples and Clips9 sheetsCross-cut, 5 x 18 mmStaples and clipsn/an/a
Aurora AU1210MA 12-Sheet Micro-Cut Shredder with Small ClipsBest Long-Run PickAurora AU1210MA 12-Sheet Micro-Cut Shredder with Small Clips12 sheetsMicro-cut, 5/32 x 15/32 inSmall paper clipsn/a60 minutes
Locksworth 110-Sheet Auto Feed Micro-Cut Shredder, 6.9 GalBest Auto-Feed PickLocksworth 110-Sheet Auto Feed Micro-Cut Shredder, 6.9 Galn/aMicro-cut, P-4n/a6.9 gal with castersn/a
Bonsaii 6-Sheet Cross-Cut Shredder with Staples, 3.4 Gal BinBest Budget PickBonsaii 6-Sheet Cross-Cut Shredder with Staples, 3.4 Gal Bin6 sheetsCross-cut, 5 x 14 mmn/a3.4 gal with window4 minutes

Pulling staples is the most boring chore in paper shredding, and it is also the reason many people give up and bin their documents whole. A shredder that accepts fasteners saves real time, but the claim hides important limits about how many staples, what size and in which mode.

Hardened steel in a staple is tougher than the paper around it, so cutters wear faster when fasteners go through. The good machines use stronger cutters and a clean cut type, while the cheap ones accept a staple but pay for it in dull blades. Knowing what a machine really accepts is the first step to buying well.

Before you buy

6 Criteria to Look For Before Buying a Paper Shredder for Staples and Paper Clips

  1. 01

    Where fasteners are allowed

    Some machines accept staples in the main slot, others only in a manual mode. The Amazon Basics 15-sheet takes staples and small clips directly, while the Locksworth 110-sheet auto tray takes paper only. Read where the fasteners go before you buy, because a tray that rejects them reintroduces the pre-sorting chore.

  2. 02

    Fastener size limits

    Staples and small paper clips are one thing; heavy binder clips, fold-back clips and paper-clip chains are another. The Aurora AU1210MA names small paper clips specifically, and the Bonsaii models list staples and clips without a size. Remove anything bigger than a standard clip by hand.

  3. 03

    Cutter wear over time

    Steel wears cutters faster than paper does. A micro-cut head like the Bonsaii 12-sheet has more cutting edges meeting each staple than a cross-cut head like the Bonsaii 9-sheet. Expect shorter blade life if you feed staples daily, and oil the cutters more often.

  4. 04

    Cut type and security

    Cross-cut handles fasteners with less strain, while micro-cut gives finer fragments. The Amazon Basics 15-sheet leaves 5.1 by 25.4 mm strips, the Bonsaii 9-sheet 5 by 18 mm, and the Aurora about 5/32 by 15/32 inch. Match the cut to the sensitivity of the paper, not just the staple load.

  5. 05

    Stack size with staples

    Rated capacity assumes clean paper. A stapled packet counts as thicker, so derate by 2 to 4 sheets. A 9-sheet Bonsaii handles about 6 to 7 stapled pages in practice, while a 15-sheet unit handles 11 to 13.

  6. 06

    Run time and bin size

    Stapled batches take longer because you feed fewer sheets per pass. The Aurora runs 60 minutes with a 300-sheet basket, while the Bonsaii 6-sheet runs 4 minutes with a 3.4-gallon bin. For big batches pick the longer cycle.

Detailed reviews

The 6 best paper shredders for staples and paper clips, explained

01
Amazon Basics 15-Sheet Cross-Cut Shredder, 6 Gal, Staples OK
15-sheet cross-cutP-4 securityStaples and clips6 gal bin
Check price on Amazon
Best for: Households that want to drop stapled documents straight into the slot.

Sorting staples out of a stack of paperwork is exactly the job this machine removes. The listing states that 15 sheets of 20 lb paper go through at once, staples and small paper clips included, which makes it the clearest on-the-record answer to the fastener question in this guide.

The cutters produce pieces of about 5.1 by 25.4 millimetres at P-4, a sensible level for household records. The entry is 8.7 inches wide, so a letter page feeds without folding. CDs, DVDs and cards go through a dedicated slot, which keeps the plastic away from the paper feed and lets the main cutter focus on sheets and fasteners.

Ownership comes down to cutter wear. Staples are steel, so each one adds a tiny amount of wear, and the cutters will not last forever if you feed staple-heavy stacks daily. A 6-gallon wastebasket holds the confetti comfortably. Choose it over the Bonsaii 9-sheet if your stacks regularly reach 12 pages with staples attached.

What works

  • Explicitly accepts staples and small clips
  • 15-sheet head clears stapled stacks
  • Dedicated slot for CDs and cards
  • 6-gallon basket is roomy

Watch out for

  • Cutters wear faster with heavy staple use
  • Long strips are less secure than micro-cut

Spec sheet

Capacity
15 sheets
Cut
Cross-cut, 5.1 x 25.4 mm
Fasteners
Staples and small clips
Entry
8.7 in wide
Bin
6 gal wastebasket
02
Bonsaii 12-Sheet Micro-Cut Shredder with Clips, Staples, 5.5 Gal
12-sheet micro-cutP-4 securityClips and staples5-min run
Check price on Amazon
Best for: People who staple sensitive paperwork and want fine particles.

This model lists cards, paper clips and staples among the things it takes, and it does so with a micro-cut head. That is a harder combination than it sounds, because tiny cutting teeth meet steel more often and wear faster than coarser cross-cut teeth.

A patented cooling system allows five minutes of continuous running. That is shorter than the 6 minutes you get on some cross-cut siblings, but adequate for a stapled stack of a few dozen pages. The 5.5-gallon bin holds about 350 sheets of A4, so it will handle a good session before it asks to be emptied.

Over several years, expect to oil the cutters and keep fasteners to a reasonable number per stack. The fine particles are the reward: a stapled bank statement ends up as dust. Compared with the Amazon Basics 15-sheet, you trade three sheets of capacity and some speed for a finer cut. Pick it for security first and convenience second.

What works

  • Micro-cut P-4 leaves tiny particles
  • Takes staples, clips and cards
  • 5.5-gallon bin holds about 350 sheets
  • Cooling system supports a five-minute run

Watch out for

  • Staples wear fine teeth faster
  • Three fewer sheets than the 15-sheet pick

Spec sheet

Capacity
12 sheets
Cut
Micro-cut, P-4
Fasteners
Staples, paper clips, cards
Run time
5 minutes
Bin
5.5 gal, about 350 sheets
03
Bonsaii 9-Sheet Cross-Cut Shredder for Home, Staples and Clips
9-sheet cross-cutP-4 security5 on, 40 offStaple and clip
Check price on Amazon
Best for: Small households shredding a modest stack of stapled mail.

Built for a spare room, this is a P-4 cross-cut unit with pieces of about 5 by 18 millimetres, shorter than the long strips on the Amazon Basics 15-sheet. It lists staples and clips among the things it can handle and gives a clear claim for output: about 180 sheets in one five-minute run, then a 40-minute cooldown.

The 40-minute rest is long, so this is a machine for a single batch, not a marathon. The nine-sheet head means a stapled pack of about eight pages is its comfortable limit. It is also lighter and smaller than the bigger units here, which makes it easier to store between uses.

In practice, treat the staple tolerance as an allowance, not an invitation. One staple per packet is fine, and a stack with clusters of fasteners will wear the cutters. It sits in a lower price tier than the micro-cut model, so it fits a household that wants a tidy, affordable, general-purpose shredder.

What works

  • Shorter 5 x 18 mm pieces for better security
  • Handles staples and clips
  • About 180 sheets per five-minute run
  • Light body is easy to store

Watch out for

  • 40-minute cooldown after each run
  • Nine sheets is the limit for stapled packs

Spec sheet

Capacity
9 sheets
Cut
Cross-cut, 5 x 18 mm
Cycle
5 minutes on, 40 off
Run output
About 180 sheets per run
Fasteners
Staples and clips
04
Aurora AU1210MA 12-Sheet Micro-Cut Shredder with Small Clips
12-sheet micro-cut60-min runSmall clips300-sheet basket
Check price on Amazon
Best for: Offices that shred stapled paperwork for an hour at a time.

Stapled paperwork piles up in offices, and this Aurora is built for the long haul with a 60-minute run time. It destroys small paper clips, CDs, DVDs and credit cards, with a micro-cut particle of about 5/32 by 15/32 inch at P-4.

The small print matters: the listing names small paper clips, so be careful with heavy-duty clips and large binder clips. The 12-sheet head works for stapled packs, and a basket of about 300 sheets stops you from emptying too often during a long job.

It is the most office-oriented machine here, which shows in the price tier and the commitment to an hour of continuous run. If you shred on weekends in big batches, this is a serious tool. The trade is that it is a slower, fine-cut machine, so it moves fewer sheets per minute than the 15-sheet cross-cut. For a staple-heavy workload, make sure to keep cutters oiled per the manual.

What works

  • 60-minute run suits big stapled batches
  • Micro-cut particles near 5/32 x 15/32 inch
  • Destroys small clips, CDs, DVDs and cards
  • Basket holds about 300 sheets

Watch out for

  • Only small clips are named
  • Slower than a 15-sheet cross-cut

Spec sheet

Capacity
12 sheets
Cut
Micro-cut, 5/32 x 15/32 in
Run time
60 minutes
Fasteners
Small paper clips
Basket
About 300 sheets
05
Locksworth 110-Sheet Auto Feed Micro-Cut Shredder, 6.9 Gal
110-sheet auto trayP-4 micro-cut60-min auto run6.9 gal bin
Check price on Amazon
Best for: Large paper piles where only a few packets carry fasteners.

Auto-feed shredders and fasteners are an awkward mix, and this Locksworth is honest about it. The listing says auto mode shreds paper only, so staples and clips go through manual mode instead. That is the correct design, because a tray that cannot see a staple will happily feed it into the cutter.

In auto mode the machine takes up to 110 sheets and runs for 60 minutes, which suits a long job of unstapled paper. The P-4 micro-cut head turns pages into tiny pieces, and the 6.9-gallon bin has a window and casters for easy emptying.

Plan on a two-step workflow. Pull staples from bulk stacks and load the tray, then use manual mode for the occasional stapled packet. If you rarely have staples, the auto tray is a time saver. If you have them constantly, the Amazon Basics 15-sheet is a simpler fit because it takes staples straight from a manual slot with no sorting.

What works

  • 110-sheet auto tray with a 60-minute run
  • Micro-cut P-4 particles
  • 6.9-gallon bin has casters and a window
  • Manual mode handles non-paper items

Watch out for

  • Auto mode takes paper only
  • Staples require the manual route

Spec sheet

Auto tray
110 sheets
Cut
Micro-cut, P-4
Auto run time
60 minutes
Bin
6.9 gal with casters
Auto mode
Paper only
06
Bonsaii 6-Sheet Cross-Cut Shredder with Staples, 3.4 Gal Bin
6-sheet cross-cutP-4 security4-min run3.4 gal bin
Check price on Amazon
Best for: Light use where a few stapled sheets need to disappear.

The cheapest tier in the guide still lists staples and credit cards among the items it shreds. Particles measure about 5 by 14 millimetres at P-4, which sits between the cuts on the Bonsaii 9-sheet and the Amazon Basics 15-sheet.

Its four-minute run and 20-minute cooldown are modest but the rest period is the shortest here. A handle on the head helps lifting, and the 3.4-gallon bin has a clear window so you can see when it is time to empty. The six-sheet head is small, so a stapled pack of five pages is the practical maximum.

This is the machine for a few documents a week. Do not expect it to digest big stapled bundles, and keep the stack well under its rating when metal is present. For a household that wants a basic staple-tolerant unit under the desk, it is enough. Spend up to the Bonsaii 9-sheet if your packs run longer.

What works

  • Lists staples and credit cards
  • Rests only 20 minutes after a run
  • Handle makes lifting the head easy
  • Clear bin window shows fullness

Watch out for

  • Six sheets is a small stack
  • Four-minute run limits bigger jobs

Spec sheet

Capacity
6 sheets
Cut
Cross-cut, 5 x 14 mm
Run time
4 minutes
Cool-down
20 minutes
Bin
3.4 gal with window

Spec sheet decoder

What the numbers on the box really mean

The specs manufacturers lead with, translated into what they tell you about real-world performance.

Staple capacity

The listing wording on fasteners, which may mean only a few at a time or any amount in the stack.

Watch forThe Amazon Basics 15-sheet states staples are fine, while the Locksworth auto mode is paper only.

Cut dimensions

Particle size in millimetres. Smaller means higher security and more wear.

Watch forThe Bonsaii 6-sheet is 5 by 14 mm, against 5.1 by 25.4 on the Amazon Basics.

Run time and cooldown

Minutes of work before a thermal stop and the rest afterwards.

Watch forThe Bonsaii 9-sheet needs 40 minutes off after 5 minutes on.

Sheet capacity

Maximum clean sheets per pass. Staples and folds reduce it.

Watch forDerate 2 to 4 sheets on any of these for stapled packets.

Security level

P-4 limits particle area for personal data. Micro-cut often reaches it more comfortably.

Watch forAll six lineup items list P-4 security or equivalent.

Methodology

How We Evaluated These Paper Shredders for Staples and Paper Clips

Fastener policy

We read what each machine says about staples and clips, noting where they must be fed. The Amazon Basics 15-sheet and Bonsaii models are explicit. The Locksworth routes fasteners to manual mode and the Aurora names small clips only.

Cutter strain

We compared cut type and teeth density to judge likely wear. Cross-cut units strain less than micro-cut. The Aurora AU1210MA and Bonsaii 12-sheet micro-cut get extra credit for staying in service despite finer teeth.

Practical capacity

We derated sheet counts for stapled packets, since fasteners add thickness. A 15-sheet unit behaves like a 12-sheet one on stapled stacks. This is based on spec sheets and owner feedback patterns.

Session length

We compared run time and cooldown, from 4 minutes on the Bonsaii 6-sheet to 60 on the Aurora and Locksworth. Stapled loads feed more slowly, so longer cycles help.

Ownership

We considered bin size, casters and windows, and the upkeep of oiling cutters. The Locksworth's wheeled 6.9-gallon bin and the Amazon Basics 6-gallon basket reduce emptying effort.

Decision guide

How to Choose the Right Paper Shredders for Staples and Paper Clips

By Fastener Habit

SituationPickWhy
Staples on most documentsAmazon Basics 15-SheetTakes staples straight from the stack
Staples on sensitive documentsBonsaii 12-Sheet Micro-CutFine fragments and staple tolerance
A few stapled packets in a big pileLocksworth 110-SheetManual mode for fasteners
Small paper clips onlyAurora AU1210MANames small clips specifically

By Budget

SituationPickWhy
Lowest tierBonsaii 6-SheetLists staples at the cheapest tier
Value for a householdBonsaii 9-SheetStaples and clips with a small body
Mid tier for convenienceAmazon Basics 15-SheetLarge head and bin
Upper tier for office useAurora AU1210MA60-minute run

Cross-Cut vs Micro-Cut

Cross-cut

The Amazon Basics 15-sheet, Bonsaii 9-sheet and Bonsaii 6-sheet use cross-cut. Staples strain the teeth less and the machines run cooler.

Micro-cut

The Bonsaii 12-sheet, Aurora AU1210MA and Locksworth 110-sheet use micro-cut. You gain finer particles but wear the teeth faster with staples.

Pick cross-cut for staple-heavy stacks and micro-cut for sensitive files.

By Stack Size With Staples

SituationPickWhy
Packets of 10 to 12 pagesAmazon Basics 15-SheetHeadroom after derating
Packets of 6 to 8 pagesBonsaii 9-SheetMatches the derated capacity
Packets of 5 pages or fewerBonsaii 6-SheetSmall but adequate
Mixed batches over an hourAurora AU1210MALong run with a large basket

For Office Paperwork Specifically

Look for

Look for a 12-sheet head or larger, a 30-minute run or longer, and wording that confirms staples. Check the size of clips allowed.

In this comparison

The Amazon Basics 15-sheet is the most practical for daily stapled paperwork. The Aurora AU1210MA is the better pick for long sessions.

When to Spend More

Spend more if

Spend more if staples are everywhere or the paper is sensitive. The Bonsaii 12-sheet micro-cut and Aurora AU1210MA give finer particles and longer duty.

Save if

Save if stapled packets are rare. The Bonsaii 6-sheet or 9-sheet covers a few packets a week.

Ownership

Maintenance schedule

The upkeep that decides whether this machine lasts two seasons or ten.

TaskIntervalWhy it matters
Oil the cuttersEvery 1 to 2 monthsStaples scrape the teeth and paper dust gums them up. Oil reduces friction and keeps jams away.
Check for loose staplesEach time the bin is emptiedA stray staple left in the bin can jam the cutter head. Remove them when you empty.
Empty the binAt half fullMetal shards add weight and pack tightly. A full bin presses the cutters.
Respect the cooldownAfter each runStaples add load. A thermal rest protects the motor.
Inspect the cuttersYearlyChipped teeth leave strips of paper and strain the motor. Replace a unit with visible damage.

FAQ

Frequently Asked Questions

Can all shredders take staples?

No. Some accept them in the main slot, others only in manual mode, and a few do not at all. Check the listing and the manual before feeding. If the wording only says the machine shreds paper, assume fasteners are not welcome, because a quiet listing usually means the maker did not design or rate the cutters for metal.

Do staples damage the cutters?

Over time they dull them. Cross-cut cutters handle staples better than micro-cut, but all steel shortens blade life. Oil the cutters and avoid heavy clusters. Spreading staples across several passes rather than feeding a thick packet with a metal-heavy corner is the simplest way to keep blade life long.

Can I shred binder clips?

Not in most machines. Small paper clips are commonly accepted, while binder clips and large fasteners should be removed. Spiral bindings, plastic combs and metal rings are also best taken off first, since they are thicker than anything the cutters are sized for.

How many stapled pages can I feed?

Take 2 to 4 sheets off the rating. A 15-sheet unit handles about 11 to 13 stapled pages.

Is micro-cut or cross-cut better with staples?

Cross-cut strains less. Micro-cut gives finer pieces but wears faster. Choose by what the paper contains. A household that mostly shreds stapled utility bills can stay with cross-cut, while someone destroying tax files with a staple in every corner should accept the extra wear of micro-cut for the finer result.

Is it safe to feed staples through the auto tray?

Only if the manual says so. Some auto trays are paper only, such as the Locksworth, and fasteners go in manual mode. Treat that rule as a feature, since it keeps hard metal away from a tray that runs unattended for an hour.

Bottom line

The short version

Browse more paper shredders for staples and paper clipson Amazon →
James Miller, Lead Machine Editor

About the author

James Miller

Lead Machine Editor, MachineFanatic

James Miller leads MachineFanatic's buying guides, turning spec sheets, manuals and owner feedback into clear verdicts on power tools, outdoor power equipment, shop machines and kitchen machines.

More from James →

Keep reading

Related guides