Amazon affiliate links - we earn a commission.Affiliate disclosure

How-to · 13 min read · Updated 2026-11-19

How to Mix 2 Stroke Fuel: Ratios, Math and Mistakes

Mix 2 stroke fuel correctly: 50:1 means about 2.6 ounces of oil per gallon. Get the ratio chart, the steps, the ethanol rules and the common mistakes.

James MillerBy James MillerLead Machine Editor
Man using a gas chainsaw to cut a fallen branch in a backyard

What a mix ratio means

Fifty to one sounds like a recipe, but it is just a proportion. A 50:1 mix means fifty parts of gasoline for every one part of oil, measured in the same units. Put a gallon of gas in a can, add the right small measure of oil, shake it, and you have fuel a 2 stroke engine can run on. The oil is not a fuel additive in the usual sense. It is the engine's only lubrication.

A 2 stroke has no oil sump, so the oil travels through the engine in the fuel. It coats the bearings, the piston and the cylinder wall, then burns off in the exhaust. Too little oil leaves parts unprotected and can seize the engine. Too much oil fouls the spark plug, clogs the exhaust and makes smoke. The ratio is the balance point the maker chose for that engine.

If you are still deciding whether a 2 stroke is the right engine at all, our comparison of 2 stroke and 4 stroke engines explains how each works and where each belongs.

Find the ratio for your tool first

There is no single correct ratio for every machine. Most modern trimmers, blowers and chainsaws from major brands specify 50:1 when used with the maker's own oil, but older tools, some brands and tools run on other oils can call for 40:1, 32:1 or a different number. The ratio belongs to the engine, so the engine's manual wins over any can of oil or internet chart.

  1. Check the fuel cap. Many tools print the ratio on the cap or on a decal beside the tank.
  2. Read the owner's manual under fuel and lubrication.
  3. If you lost the manual, search the model number on the manufacturer's site.
  4. Read the oil bottle. It lists the ratios it is made for. Use the one that matches your engine.
Important: when the tool and the oil bottle disagree, follow the tool. If the manual calls for a ratio the oil is not rated for, switch oils rather than changing the ratio.

The math, done once

A US gallon holds 128 fluid ounces. To find the oil needed, divide 128 by the ratio's first number. For 50:1, 128 divided by 50 is 2.56 ounces, and bottles round this to 2.6 ounces. For 40:1 it is 3.2 ounces. For 32:1 it is exactly 4 ounces. For 25:1 it is about 5.1 ounces.

For metric, the oil volume in milliliters per liter is 1,000 divided by the ratio. For 50:1 that is 20 milliliters per liter. For 40:1 it is 25 milliliters per liter.

RatioOil per 1 US gallonOil per 2 gallonsOil per 5 gallonsOil per liter
50:12.6 oz5.1 oz12.8 oz20 ml
40:13.2 oz6.4 oz16 oz25 ml
32:14 oz8 oz20 oz31 ml
25:15.1 oz10.2 oz25.6 oz40 ml

A quick check on any batch: divide the gasoline volume by the oil volume, and the answer should land near your ratio. If you pour 2.6 ounces into one gallon, 128 divided by 2.6 is about 49, which is close enough to 50:1 for any engine. Be careful with metric and US units, because an imperial gallon is larger than a US gallon, and a measuring cup in one system will give a wrong dose if you apply the other system's table. Pick one system, stay with it, and write the dose on the can lid. Most chainsaw and trimmer owners only mix a gallon or less. For small tanks, such as a 0.5 liter chainsaw tank, mix a small can rather than filling the tool from a large batch you will not finish.

What you need before you mix

  • Fresh gasoline. Pump fuel with no more than 10 percent ethanol, or ethanol-free fuel when you can get it. Do not use fuel that has sat for months.
  • The right oil. Oil labeled for air-cooled 2 stroke engines and for your ratio. Do not use car engine oil or outboard oil unless your manual specifically allows it.
  • An approved fuel container. Use a clean, labeled, approved gasoline can. A can with a graduated mixing chamber or measuring marks is useful.
  • A measuring cup or pre-measured bottle. Many oils come in single-gallon sized bottles.
  • A funnel or spout with a filter, to keep dirt out of the tank.
Gas chainsaw held in a hand, an engine that runs on mixed fuel
A gas chainsaw. Its engine takes all its lubrication from the oil mixed into the fuel.

Step by step: how to mix

  1. Work outdoors, away from sparks, flames and anything that could ignite vapor. Do not smoke.
  2. Put the empty can on the ground or a level surface, not on a truck bed liner or in a vehicle, so static does not build up.
  3. Pour about half of the gasoline you plan to mix into the can.
  4. Add the correct measure of oil for the full amount of gasoline.
  5. Pour in the rest of the gasoline. This helps the oil mix in as the fuel moves.
  6. Close the can and shake it gently for about 30 seconds, until the fuel looks uniform in color.
  7. Label the can with the ratio, the date and the word MIXED.
  8. Fill your tool's tank, wipe up any spills and close the cap tightly before you start the engine.

Pouring oil first and then fuel also works, as long as you shake well. What matters is that the oil is evenly distributed before you pour it into the tank. If you see oil sitting in streaks or clinging to the bottom, shake again.

Premixed fuel in a can

Pre-blended 2 stroke fuel is sold in cans at hardware and home stores. It is usually ethanol-free, uses stabilized fuel and a fixed ratio, most often 50:1, and it keeps far longer than pump gasoline mixed at home. It is much more expensive per gallon, but if you only use a trimmer for a few hours a year, a can of premix lasts for many tanks and removes the guesswork.

Check that the ratio on the can matches the ratio your engine requires. Premix at 50:1 is wrong for an engine specified at 40:1 or 32:1, and the can's label will tell you which it is.

OptionBest forDrawback
Mix your ownRegular users, larger tanks, cost-conscious ownersYou must measure and keep it fresh
Premixed canOccasional users, small tanks, long storageHigher cost per gallon, fixed ratio

Ethanol and fuel age

Gasoline is a mixture that changes as it ages. Light components evaporate, and oxidation forms gum and varnish. Fuel that contains ethanol also attracts moisture from the air, and in a tank sitting for weeks that water can separate and sink, leaving a layer that corrodes parts and starves the engine. Small-engine makers generally accept gasoline with up to 10 percent ethanol and do not approve E15, which pump labels warn against for equipment such as chainsaws and lawn mowers.

Shelf life figures differ between manufacturers, so read your manual. One major small-engine maker puts the useful life of ordinary gasoline at about 30 days. Stabilizer slows aging but cannot restore fuel that has already gone stale. For mixed fuel, a good practice is to mix only what you expect to burn within a month, and to label the date on the can.

Season rule: if a tool will sit for more than a month, either run the tank dry or use fresh stabilized fuel at the start of the season. Do not leave a half tank of old mix in the carburetor over winter.

Choosing the right 2 stroke oil

Not all 2 stroke oils are equal, and the label tells you what each is made for. Oils rated for air-cooled engines, such as those in trimmers and chainsaws, are formulated to handle the high heat of an engine with no liquid cooling. Oils made for water-cooled outboard engines are a different formulation, and using one in an air-cooled tool without approval can leave deposits.

  • Maker-branded oil. Often the safest, since the ratio on the tool matches the oil.
  • Universal air-cooled oil. Many brands list that they work from 32:1 to 100:1. Check the label for your ratio and the standards it meets.
  • Synthetic or semi-synthetic. They tend to burn cleaner and leave fewer deposits, but they are not mandatory. Use what the manual allows.
  • Dye. Many oils are tinted so you can see that the oil has been added. That tint is a handy check.

Whichever oil you choose, buy fresh and store the bottle sealed. Oil that has sat open and picked up dirt or moisture is not worth the risk.

Common mistakes and what they do

MistakeWhat happensFix
No oil in the fuelEngine runs hot, parts wear fast, can seize in minutesStop, drain, refill with correct mix, inspect
Too little oilHot running, scoring, shortened lifeRemix to the right ratio
Too much oilSmoke, fouled plug, carbon in the exhaust, hard startingDrain, remix, clean plug
Wrong oil typeDeposits, plug foulingUse air-cooled rated oil
Old, stale mixHard starts, rough running, gummed jetsUse fresh fuel only
Mixing in the tool tankUneven lubricationAlways mix in a separate can first
Guessing the measureWrong ratioUse a measuring cup or pre-measured bottle

A rich mix is the safer error than a lean one. More oil than needed makes smoke and fouls plugs, but too little oil can destroy the engine in a single tank. If you are unsure, check the manual, and when in doubt do not run the engine until you are certain.

If you put mixed fuel in a 4 stroke, or straight gas in a 2 stroke

These are the two mistakes that send people searching. Straight gas in a 2 stroke is the serious one. If you realize before starting the engine, drain the tank and carburetor and refill with correct mix. If you already ran it, stop immediately, because every minute without lubrication adds wear, and have the engine checked if it ran for more than a short time.

Mixed fuel in a 4 stroke is far more forgiving. The engine will smoke and the plug can foul, but a tank or two seldom causes lasting damage. Drain the fuel, replace it with plain gasoline, and replace the spark plug if the engine runs poorly. Follow the manual for your own machine.

Chainsaw cutting a branch in a backyard
A chainsaw working. Running it on correctly mixed fuel is what keeps the engine lubricated under load.

Safe fuel handling

Gasoline vapor ignites easily, and a small spill near a hot engine is a real hazard. Follow these basics, along with the safety section in your manual.

  • Fill the tool outdoors, on a bare level surface, with the engine off and cool.
  • Do not smoke or work near open flame, pilot lights or sparks.
  • Store fuel in approved, labeled containers, away from living space and heat.
  • Do not fill the tank to the brim. Leave room for expansion.
  • Wipe spills and move at least ten feet from the fueling spot before starting the engine.
  • Keep fuel out of reach of children and animals.

These steps matter most with chainsaws, which are often fueled in the field. If you cut often, our guide to sharpening a chainsaw chain and chainsaw bar length cover other parts of the routine.

Storing mixed fuel and the tool

Mixed fuel ages like any other gasoline, with the added complication that the oil can separate slightly over long storage. Keep it in a cool, shaded, sealed container, and shake it before each use. After about a month, do not trust it for a high-value tool. Pour old mix into a clean can and take it to a fuel disposal or recycling site rather than dumping it.

For the tool itself, you have two choices at the end of a season. Run the engine until it uses up the fuel in the carburetor, or fill with fresh stabilized fuel and run it for a couple of minutes to circulate it. Either approach avoids stale fuel gumming the jets over winter. For related long-term care on larger engines, see our guide to storing a generator for the off season.

What this means when you buy a tool

The fuel routine is part of the cost of owning a gas tool. If you will not mix fuel carefully, or you use a trimmer or saw only a few times a year, a battery tool avoids this chore entirely. Compare options in our cordless chainsaw guide before you commit to gas, and see how smaller models compare in the entry-level mini chainsaw group, the next tier and the one above it.

If you stay with gas, keep the process simple: one ratio per household if possible, one brand of oil, one labeled can, and a habit of mixing small batches. Most fuel trouble comes from complexity, such as old cans, unlabeled bottles and two tools with different ratios sharing a shelf.

Frequently Asked Questions

How much oil do I add to a gallon of gas for 50:1?

About 2.6 fluid ounces. The exact figure is 2.56 ounces, which bottles round to 2.6. In metric, that is 20 milliliters of oil per liter of gasoline.

Can I use car engine oil in a 2 stroke?

Do not. Car oil is not designed to burn with fuel in an air-cooled 2 stroke and leaves deposits and smoke. Use oil labeled for 2 stroke air-cooled engines and for your ratio.

How long does mixed fuel last?

Plan on about a month for pump gasoline mixed at home, since gasoline starts to degrade within weeks. Stabilizers and ethanol-free or premixed fuel last longer, but manufacturers differ on how long, so check the manual.

What if I added too much oil?

Expect smoke and a fouled spark plug, but the engine is usually safe. Drain the tank, refill with correct mix and clean or replace the plug. A rich mix is less damaging than a lean one.

Do I mix the oil in the tool's tank or in a can?

Mix in a separate can, then fill the tool. Pouring oil and gas separately into the tank leaves poor mixing, and the engine can draw unmixed fuel.

Can I use the same mix for my trimmer and chainsaw?

Often yes, if both specify the same ratio, which is commonly 50:1 for modern tools. Check each manual, because some older or different-brand tools need a different ratio.

Is premixed canned fuel worth using?

For occasional use, yes. It is ethanol-free, stabilized and holds its quality far longer than fuel mixed at home. Confirm that its ratio matches your engine.

Bottom line

Find your tool's ratio on the cap or in the manual, divide 128 ounces by the ratio's first number to get the oil per gallon, and for 50:1 use about 2.6 ounces. Use fresh gasoline with no more than 10 percent ethanol, oil rated for air-cooled 2 stroke engines, a clean approved can and a good shake. Mix only what you will use within about a month, label the can, and never run a 2 stroke on straight gas. If mixing fuel is a chore you will skip, a battery tool or a can of premix is the safer answer.

James Miller, Lead Machine Editor

About the author

James Miller

Lead Machine Editor, MachineFanatic

James Miller leads MachineFanatic's buying guides, turning spec sheets, manuals and owner feedback into clear verdicts on power tools, outdoor power equipment, shop machines and kitchen machines.

Keep reading

Related on MachineFanatic

Image credits

  • chainsaw-cutting-branch.webp: Kampus Production, CC BY 2.0
  • chainsaw-in-hand.webp: Richard Allaway, CC BY 3.0